Siemens simatic panel touch manual

Entering "0" disables the screen saver. Follow the procedure below to configure transfer mode. This can result in personal injury or material damage. Open the "System Properties" dialog using the "System" icon. Open the "Transfer Settings" dialog using the "Transfer" icon. Change to the "Directories" tab. Procedure Proceed as follows: 1. With a high number of alarms, the internal flash memory is subject to an equally high number of read and write cycles.

You need to back up the registry settings to flash memory after installation or removal. You can also save the data in the memory buffer to flash memory. If the printer selected can print in color and you wish it to do so, select the "Color" check box.

This allows you to improve the color quality for the printed pages. Change to the "Firmware" tab. The following firmware versions are displayed. Enter the homepage for the Internet browser in the "Start Page" text box. Enter the address of the default search engine in the "Search Page" text box. If you want to use your own browser, enter its homepage in the "User Agent" text box. The browser must then be launched. If you want to use a proxy server, select the "Use a proxy server" check box.

Specify the address and port of the proxy server. Only the start of the addresses is required. Open the "Internet Options" dialog using the "Internet Options" icon. Change to the "Security" tab. Adjust the settings to current requirements. You can find additional information on the options in this dialog on the Microsoft website. Confirm your entries. The dialog closes. The trusted websites are now set. Use the "Import.. Confirm your entries with "OK".

The list of certificates on the HMI device is updated. These include: — Restriction to characters letters, digits, hyphen or point — A name component within the device name, for example, a string between two points, may not exceed 63 characters.

Change to the "NTP" tab. If you want to use the time of a time server, activate "Automatically synchronize with …". If necessary, enter a description for the HMI device in the "Device description" text box. The computer name for the HMI device is now set.

If a name server is used in the local network, open the "Name Servers" tab. The following dialog appears: 6. Enter the respective addresses in the text boxes. If you want to make further settings for sending e-mails over an SMTP server, press the "Advanced" button. Change to the "Remote" tab. Select the options for starting and closing the Sm rtServer. Change to the "Web Server" tab. In the "Tag acces" group, define the type of access to the tags of the server HMI device.

In the "Authorizations" tab you specify the Web authorizations. Save the settings using "Apply" and close the dialog box with "OK". Confirm your entries with "Save". Press the "Next" button. If you only want to backup compatible files, select the "compatible files only" check box. A restore operation deletes the old data from flash memory of the HMI device on confirmation. The following dialog is displayed. Select the required file in the "Backup files on" group. If you need information about the selected file, press the "Details" button.

The "Update OS image from external memory" dialog is displayed. The "0 devices found" message appears if there is no storage medium in the HMI device or if it is defective. To restore the data of the selected file, press the "Update" button. The "Update settings" dialog is displayed. The dialog informs you that the settings in the Control Panel will be kept and offers you the option of keeping or deleting license keys present on the HMI device. The projects that are located on the external storage medium are displayed in the following dialog.

The following figure shows an example. Select the project that you want to load into the HMI device. Press the "Details" button to receive additional information about the selected project. Press the "Load" button to transfer the project data with the selected options to the HMI device.

The new project starts on the HMI device after the load operation. Enabling and disabling automatic backup 1. The target device can be a controller or another HMI device. Select the target device whose IP address and device name you want to change. The "Flash" Page "Passive Listening" to ensure interruption-free communication; see the following figure. You can find additional information on configuration in the information system of the TIA Portal.

Double-click "Add new device" in the project tree. Page Configuring the Mobile Panel 6. Click the icon of the controller. Under "Ethernet addresses", click on the "Add new subnet" button. Under "IP protocol", assign a unique IP address to the controller in the subnet. Select "Finish". The Mobile Panel is added to the project. Double-click on "Device configuration". Click on the icon of the HMI device. Select the "Manual assignment of F-monitoring time" check box and enter the following values at the indicated locations.

The default value is ms. This section describes the configuration using an example of an SF-type controller. Other compatible fail-safe controllers are configured in the same way. Do the same for the following application scenarios: — Configuring plant areas in WinCC 6. Select "ActivateScreen". Select an existing screen or create a new screen for the selected zone. The plant areas are assigned the required screens. For example, the keyswitch can be used to lock certain functions.

Evaluation is run as soon as the HMI device is connected to a connection box. Page Commissioning A Project Commissioning a project Overview Configuration phase A project — the process image of the working process — is produced during configuration to visualize automated working processes.

The process displays for the project contain displays for values and messages which provide information about process statuses. The process control phase follows the configuration phase. Page Using Existing Projects Commissioning a project 7.

You can operate the plant with the HMI device in accordance with the configuration. Proceed as described in the section "Configuring transfer Page ".

Page Commissioning a project 7. Page Testing A Project Commissioning a project 7. Page Backup And Restore Commissioning a project 7. Select the HMI device type on the "General" tab. This is caused by differences between the versions of the configuration software used and the HMI device image available on the HMI device.

Page 5. Select the "OS Update" tab. Set "Transfer" mode on the HMI device. Page Under "Image path", select the HMI device image file "filename. Page Managing Wincc Options Commissioning a project 7.

The required license keys are usually supplied on a storage medium, for example, a USB stick. You can also obtain a license key from a license server. License keys can also be removed from the HMI device with drag-and-drop. You may trigger unintentional actions that could cause material damage. Never press more than one operating element on the display at once.

Page Function Keys Operating a project 8. Page Direct Keys Operating a project 8. A direct key enables operation with a short response time, for example, as required for setup mode. Page Displaying Infotext Operating a project 8.

If you enter a value outside these limits it will not be accepted, for example, "80" is rejected if the configured limit is "78".

If an alarm window is configured, a system alarm is output on the HMI device and the original value is displayed again. Page Closing The Project Operating a project 8. Depending on the configuration, infotext may also be accessed with an operating object.

Please refer to your system documentation for additional information. Page Fail-safe operation 9. The project starts as configured in the Control Panel. The project start screen appears after startup.

Page Safety-Related Dialogs Fail-safe operation 9. Acknowledge the communication error with the enabling button or confirm the communication error on the fail-safe controller. If you want to view the error codes of the fail-safe module with respect to the associated controllers, open the "Show Error List" dialog with the "Show fatal errors" link. Make a note of the entry under "Version" Page Maintenance And Care Maintenance and care Page Technical Specifications Microsoft licenses License fees for the pre-installed Microsoft operating system on the HMI devices are paid directly by Siemens to the Microsoft company.

Page Technical specifications Page Mechanical Ambient Conditions Technical specifications Page Climatic Ambient Conditions Technical specifications Page Dimension Drawings Technical specifications Page Technical Specifications Technical specifications Page Connecting Cable Overvoltage category Page Connection Boxes Technical specifications Page Power Consumption Specifications Technical specifications Note Proof-test intervals Proof-test interval of the device Lifetime : 20 years.

The device must be replaced after this, at the latest. The stop bypass only works if the connection box is supplied with power.

Page Communication With Controllers Technical specifications The specified maximum values are not additive. It cannot be guaranteed that configurations running on the devices at the full system limits will be functional. No automatic wiring is performed. The ID must be unique throughout the plant and must match the value of this parameter.

Safety functions are no longer available. If the error persists after resetting the fail-safe module, contact the Siemens hotline. Page Technical Support A.

Page Markings And Symbols Markings and symbols Safety-relevant symbols The following table describes symbols that can be added to your SIMATIC device, to its packaging or to an enclosed document in addition to the symbols described in the manuals. Page Markings and symbols B.

IP54 Devices approved for Ex Zone 22 in a control cabinet with min. Page Glossary Glossary "Automatic mode" and "setup mode" Program-controlled plants pose a significant safety risk for operators. EN "Machine tools.

Machining centers" and DIN EN " Safety of machine tools - Milling and boring machines" define operating modes to ensure staff safety. A "setup mode" is required for correct plant setup for "automatic mode". You can create projects for a plant with the configuration software. Configuration software Configuration software is software used to create projects for process visualization and input of process values. Page Glossary Infotext An infotext is a configured information on objects within a project.

Infotext for an alarm, for example, may contain information on the cause of the fault and troubleshooting routines. Totally Integrated Automation Portal — your future-proof gateway to automation in the Digital Enterprise. SIMATIC S controllers are the intelligent choice for compact automation solutions with extended communication options and integrated technology functions. They are available in standard and failsafe versions.

Siemens products for specific requirements represent high levels of robustness, efficiency, and flexibility. Explore industrial automation projects all over the world and experience for yourself industry-specific know-how in the fields of Industrie 4.

This page requires JavaScript in order to be fully functional and displayed correctly. Please enable JavaScript and reload the site.

It looks like you are using a browser that is not fully supported. Please note that there might be constraints on site display and usability. For the best experience we suggest that you download the newest version of a supported browser:. Benefits Advanced benefits for basic applications. Improved process quality Visualization allows for considerably increased process quality with compact plants or smaller applications.

Product range All Basic Panels at a glance. Standard Basic Panels. The KTP Basic is available in two versions. Basic Panels Keyless. Starter Kits. The kits comprise everything you need for an easy start at a special price. Technical documentation Manuals, Operating instructions etc. Support Services In case of an emergency, Digital Enterprise Services offer you a wide range of services - by phone and online, anytime and anywhere with online support, technical support, the Siemens Industry Service Card and Managed System Services.

Learn more. Spare Parts Services The Spare Parts Services from Digital Enterprise Services are available worldwide and ensure a smooth and fast delivery of spare parts - and thus optimal system availability. Training Services Industrial learning for every need with training services, continuously and sustainably.

AC Schwimmbadtechnik AG. Effective customer training by using visualization instead of status LEDs. Read the success story. Solinaut GmbH. Optimum resource utilization through easy realization of appealing user interfaces. Prevention of maloperation e. A product portfolio to fit all requirements. Fewer errors during configuration and maximum quality. Reduced costs for spare parts inventory and service.

Related topics.